Liquid-like materials could pave way for new thermoelectric devices
Although it is physically a solid, it exhibits liquid-like behaviors due to the way its copper atoms flow through the selenium's crystal lattice. "It's like a wet sponge," explains Jeff Snyder, a faculty associate in applied physics and materials science in the Division of Engineering and Applied Science at the California Institute of Technology (Caltech) and a member of the research team. "If you have a sponge with very fine pores in it, it looks and acts like a solid. But inside, the water molecules are diffusing just as fast as they would if they were a regular liquid. That's how I imagine this material works. It has a solid framework of selenium atoms, but the copper atoms are diffusing around as fast as they would in a liquid."
The research, led by scientists from the Chinese Academy of Science's Shanghai Institute of Ceramics in collaboration with researchers from Brookhaven National Laboratory and the University of Michigan, as well as from Caltech, is described in a paper recently published in the journal Nature Materials. A good thermoelectric material must be good at conducting electricity but bad at conducting heat. If it were good at conducting heat, the heat from the hot end would move to the cool end so fast that the whole material would rapidly reach the same temperature. When that happens, the electrons stop flowing.
One way to improve thermoelectric efficiency, then, is to decrease a material's ability to conduct heat. To that end, researchers have been developing thermoelectric materials with a mix of crystalline and amorphous properties, Snyder says. A crystalline atomic structure allows electrons to flow easily, while an amorphous material, such as glass, has a more irregular atomic structure that hinders heat-carrying vibrations from traveling.
These heat-carrying vibrations travel via two types of waves. The first type is a longitudinal or pressure wave, in which the direction of displacement—in this case, the jiggling of atoms—is the same as the direction of the wave. The second type is a transverse wave, in which the direction of displacement is perpendicular to the direction of the wave, like when you shake a jump rope up and down, resulting in waves that travel horizontally along the rope.
In a solid material, a transverse wave travels because there is friction between the atoms, meaning that when one atom vibrates up and down, an adjacent atom moves with it, and the wave propagates. But in a liquid, there is minimal friction between the atoms, and a vibrating atom just slides up and down next to its neighbor. As a result, transverse waves cannot travel inside a liquid. Ocean waves are different because they have an interface between the liquid and the air.
The team found that because heat-carrying vibrations in a liquid can travel only via longitudinal waves, a material with liquid-like properties is less thermally conductive.
Therefore, a liquid-like material that's also good at conducting electrically should be more thermoelectrically efficient than traditional amorphous materials, Snyder says. In the case of the copper-selenium material that the researchers studied, the crystal structure of the selenium helps conduct electricity, while the free-flowing copper atoms behave like a liquid, damping down thermal conductivity.
The efficiency of a thermoelectric material is quantified using a number called a "thermoelectric figure of merit." The copper-selenium material has a thermoelectric figure of merit of 1.5 at 1000 degrees Kelvin, one of the highest values in any bulk material, the researchers say.
NASA engineers first used this copper-selenium material roughly 40 years ago for spacecraft design, Snyder says. But its liquid-like properties—which were not understood at the time—made it difficult to work with. This new research, he says, has identified and explained why this copper-selenium material has such efficient thermoelectric properties, potentially opening up a whole new class of liquid-like thermoelectric materials for investigation.
Source and image: Caltech
Visit the California Institute of Technology at www.caltech.edu
- Roll clad strips with adhesive copper-aluminium bonds act as battery cell connector
- Leaded laminate copper-moly-copper base packages dissipates heat from high power compound semiconductor devices
- Texas Instruments continues drive for the adoption of copper wire bonding technology
- High-efficiency heterojunction silicon solar cells with copper electroplating
- Copper nanowires to replace ITO on mobile displays
- Aluminum busbar halves weight of battery power cabling
- ZSW uses roll-to-roll system to deposit CIGS thin-film cells on a 25 micrometre thin polymer film
- Nanotech boosting piezoelectrics, thermoelectrics
- Thermoelectrics could harvest car exhaust heat
- High-voltage thermoelectric power generators provide energy harvesting for self-powered distributed sensors
- Miniature thermoelectric power generator delivers up to 1.5 mW from a 10K temperature gradient
- Earth has enough copper for e-mobility, researchers say
- TI pushes pillar flip-chip for next-gen ICs
- Copper nanowires enable flexible displays, solar panels
- Wearable textile battery is capable of being recharged by lightweight solar cells
- Cooling without a fan
- Texas Instruments releases the industry's most extensive reference design library
- OLEDS and solar cells to come straight from the printer in future
- Digital DC/DC power controller's compensation free control loop reduces design risks and costs
- The Top 10 Most Popular Power Management News Stories of 2013
- World's smallest FM radio transmitter made from graphene
- New primary side regulation constant voltage solution in LED driver
- Self healing lithium-ion battery electrode technology could prove disruptive
- Power amplifier solution for mobile base stations doubles efficiency
- Demo Bluetooth low energy keyboard is 10x thinner than any other
- Wireless power: Accommodating new industry standards
- Selecting FETs for hot-swap source connection
- Using film and aluminum electrolytic caps in power converters for voltage stabilization in HV grids
- Bio-based solar cell uses photosynthetic proteins to generate electricity
- 3mm Ã— 3mm QFN IC Directly Monitors 0V to 80V Supplies
- Adaptive Cell Converter Topology Enables Constant Efficiency in PFC Applications
- Ultra-compact and innovative - new Schaffner IEC inlet filter series
- EMC Considerations for Switching Power Supplies
- How to Achieve Power Estimation, Reduction and Verification in Low Power Design
- Industrial-Grade Wide Temperature Assurance for Intelligent Systems
- High-voltage DC distribution is key to increased system efficiency and renewable-energy opportunities